How do I wire a 2 wire 2. It showed me that you were in chat, maybe some trouble with chat it happens from time to time, I will continue based on typical installation, if you have questions please ask, I will send a link so you may choose the correct size wire based on distance from panel to pump, also include depth of pump in distance, simply enter the information, and it will narrow down the chart, I would personally use 1.
Ok so the first thing you will need to know after sizing the wire, is breaker size if you choose 1. It must be a ground fault breaker due to electrical leakage from the motor to the open water, If your pump is within site and not over 5. LINE black to one white to the other , and wire going to pressure switch will be your LOAD also black to one white to other, remember both black and white are hots on 2. The pressure switch, You will have LINE and LOAD here as well, the wire coming from the load side of your disconnect will be your LINE in the pressure switch, and the pump will be LOAD, most times in pressure switchs the middle 2 screws are line and outer are load, so the wire coming from your disconnect the black will hook on 1 line screw the white on the other, the wire coming from the pump you will have to use submersible cable not uf cable typically it is 3 strands black red and green, in the pressure switch, you will hook black to a load screw and red to the other load screw, and be sure and ground pressure switch, you may also need to use flexible conduit on this cable into the pressure switch as well. At the pump, you will have 3 leads, 2 black and 1 green, you will need to pick up a splice kit designed for a well pump your pump may have included one, you will need to slide 1 heat shrink over each wire before crimping together, do this first, then you may use the crimp sleave that come in the kid to join the wires 1 black to black, 1 red to black, and ground/green to green, you will need a crimp too for this and be sure connections are made well, once connections are made slide the heat shrink over the connector and heat with torch, be careful not to get to hot, work torch back and forth until a glue like substance froms from ends of heat shrink, repeat on remaining 2 wires, be sure to secure wiring to water pipe, with tape, or similar soft connector,Also your ditch to in which wire is buried from house panel to pump should be 2.
At your entry point to your breaker panel you may need to use conduit to protect wire here also, from ditch to panel, as a rule of thumb conduit should be straped within 1. Installing the gfci breaker, You will need 2 open spaces together vertically in your panel the gfi breaker comes with a white pigtail attached to the breaker, this will attach to your neutral bar, your black wire will go to one screw on the breaker and white will go to the other, remember to XXXXX XXXXX wire with red tape, Also franklin pumps should not be tilted more than 1. Always get proper permits and have your work inspected especially in this case dealing with open water and electricity.
I hope I have answered most of your questions, If you need clarification on any thing feel free to ask.
![Installing Electrical Switchs Installing Electrical Switchs](http://workshop-manuals.com/volkswagen/golf-mk6/images/golf-mk6-2253.png)
![Installing Electrical Switchs Installing Electrical Switchs](http://workshop-manuals.com/volkswagen/golf-mk3/images/golf-mk3-2001.png)
I think i'm going to scrap the whole ignition kill switch because i dont know where to get a professional to do it nor do i have the money to pay for that. NOTE: There are folks that strip wires with diagonal pliers, side cutters, knives, and other things. When you are installing a $250-$300 transfer switch, you will buy.
- How much should a rewire cost. I got an estimate from a friend of a friend that came out to be 1300.00.which includes pulling old wire out and.
- Question - How do I wire a 2 wire 230v submersible well pump? - F0. Find the answer to this and other Electrical questions on JustAnswer.
- See real-world electrical Lincoln MKX repair histories as reported by other Lincoln MKX owners. Also, see repair breakdown by problem area and cost.
- Question - Installation of 3-Pole Pass & Seymour Decorator (Panel) Switches. - 1R. Find the answer to this and other Electrical questions on JustAnswer.
- Wiring a basic light switch, with power coming into the switch and then out to the light is illustrated in this diagram.
![Installing Electrical Switchs Installing Electrical Switchs](http://image.hotrod.com/f/101967984+w660+h495+cr1/23-1956-chevrolet-pickup-window-motor-switches.jpg)
![Installing Electrical Switchs Installing Electrical Switchs](http://workshop-manuals.com/volkswagen/polo-mk3/images/polo-mk3-1485.png)